10 Best Best Gps Module For Arduino of 2025

Tested and Reviewed: Top 10 Best Gps Module For Arduino deals with expert ratings from 8.1 to a perfect 10

March 2026 Edition

Editor's Choice

9.7

YELUFT

YELUFT 2pcs GY-NEO6MV2 NEO-6M GPS Module Flight Control Module Support 3.3V-5V Power Supply with Ceramic Antenna for Arduino, STM32, Raspberry Pi, ESP32

Editor's bottom line:

“This best gps module for arduino is the best one we tested. In terms of quality, brand and price, we couldn't ask for more.”

Main Highlights

Accurate Positioning: Based on NEO-6MV2, supports GPS and GLONASS, supports simultaneous tracking of 22 satellites, tracking sensitivity -162dBm, cold-start sensitivity -148 dBm, positioning accuracy up to ±2.5m in open environments, stable positioning even in complex environments such as urban canyons or dense jungles
Low Power Consumption: Supporting 3.3V-5V power supply, the continuous operating current is 67mA, 11mA in standby mode, and 1mA during sleep, which ensures the positioning accuracy while controlling the energy consumption to the maximum, especially suitable for the scenarios that are sensitive to the endurance, and significantly reduces the cost of post maintenance
Hardware Interface: Standard UART-TTL level, support 3.3V/5V dual voltage compatibility, can be directly connected to Arduino, Raspberry Pi, ESP32 and other development boards; 4Pin interface ( VCC, GND, TX, RX), reserved hardware reset pin; baud rate support 4800bps~115200bps (default 9600bps), real-time switching through AT instructions or UBX commands, to adapt to different master performance
Plug and Play: Onboard EEPROM chip operates independently of the main control chip, saves configuration parameters after power failure, and automatically reads the parameters (baud rate, positioning mode, NMEA statement screening) from the EEPROM when the power is on, eliminating the need to repeat the initialisation, and realising Plug and Play
Widely Application: Widely used in vehicle monitoring, UAV navigation, handheld terminals and other scenarios that require high-precision positioning. You can also combine with Arduino, STM32, LoRa module, etc. to quickly build GPS tracker, weather station and other IoT applications

Show Price

Picked by 397 people today

9.5

Beffkkip

2Pack GPS Module,Navigation Satellite Positioning NEO-6M,Arduino GPS, Drone Microcontroller, GPS Receiver Compatible with 51 Microcontroller STM32 Arduino UNO R3 with Antenna High Sensitivity

Main Highlights

GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage;
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect; With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned;
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna;
If you have any issue when using our product,or you need product use documentation, please contact us directly for assistance.we will reply your problem in 24 hours.We try our best to provide the most professional service for each customer.
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna

Show Price

9.5

MakerFocus

MakerFocus 2 Pack GT-U7 GPS Module Satellite Navigation Positioning GPS Receiver Drone Microcontroller Compatible with NEO-6M 51 Microcontroller STM32 Arduino UNO R3

Main Highlights

GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage
GPS baud needs to be set to 9600 instead of 4800; PPS pin is not needed unless using the GPS to drive a hardware high precision clock
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna
Note: Please use the GT-U7 GPS module in an open place, the LED will flash after the satellite signal is found. Bad weather and indoor use will affect the accuracy of positioning

Show Price

9.2

Teyleten Robot

Teyleten Robot ATGM336H GPS+BDS Dual-Mode Module Flight Control Satellite Positioning Navigator Replacement NEO-M8N NEO-6M for Arduino 2pcs

Main Highlights

Car positioning in navigation
Mobile phones, tablet PCs, handheld devices
Embedded positioning device
Wearable device

Show Price

9.0

HiLetgo

HiLetgo GY-NEO6MV2 NEO-6M GPS Flight Controller Module 3V-5V with Super Strong Ceramic Antenna for Arduino EEPROM APM 2.5

Main Highlights

Module with a ceramic antenna, superior signal
Save the configuration parameter data EEPROM Down
With data backup battery;With LED signal indicator
Default baud rate: 9600, Interface: RS232 TTL
Compatible with a variety of flight control module

Show Price

8.8

YELUFT

YELUFT 1pcs GY-NEO6MV2 NEO-6M GPS Module Flight Control Module Support 3.3V-5V Power Supply with Ceramic Antenna for Arduino, STM32, Raspberry Pi, ESP32

Main Highlights

Accurate Positioning: Based on NEO-6MV2, supports GPS and GLONASS, supports simultaneous tracking of 22 satellites, tracking sensitivity -162dBm, cold-start sensitivity -148 dBm, positioning accuracy up to ±2.5m in open environments, stable positioning even in complex environments such as urban canyons or dense jungles
Low Power Consumption: Supporting 3.3V-5V power supply, the continuous operating current is 67mA, 11mA in standby mode, and 1mA during sleep, which ensures the positioning accuracy while controlling the energy consumption to the maximum, especially suitable for the scenarios that are sensitive to the endurance, and significantly reduces the cost of post maintenance
Hardware Interface: Standard UART-TTL level, support 3.3V/5V dual voltage compatibility, can be directly connected to Arduino, Raspberry Pi, ESP32 and other development boards; 4Pin interface ( VCC, GND, TX, RX), reserved hardware reset pin; baud rate support 4800bps~115200bps (default 9600bps), real-time switching through AT instructions or UBX commands, to adapt to different master performance
Plug and Play: Onboard EEPROM chip operates independently of the main control chip, saves configuration parameters after power failure, and automatically reads the parameters (baud rate, positioning mode, NMEA statement screening) from the EEPROM when the power is on, eliminating the need to repeat the initialisation, and realising Plug and Play
Widely Application: Widely used in vehicle monitoring, UAV navigation, handheld terminals and other scenarios that require high-precision positioning. You can also combine with Arduino, STM32, LoRa module, etc. to quickly build GPS tracker, weather station and other IoT applications

Show Price

Best Value

8.6

Save 8%

Beffkkip

GPS Module Receiver,Navigation Satellite Positioning NEO-6M (Arduino GPS, Drone Microcontroller, GPS Receiver) Compatible with 51 Microcontroller STM32 Arduino UNO R3 with Antenna High Sensitivity

8% Off

Main Highlights

With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect; With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned;
GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage;
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna;
If you have any issue when using our product,or you need product use documentation, please contact us directly for assistance.we will reply your problem in 24 hours.We try our best to provide the most professional service for each customer.
How to use the GPS module better, the link is obtained in the Product guides and documents, please download it before use

Show Price

8.3

HiLetgo

HiLetgo NEO-7M GPS Satellite Positioning Module for Arduino STM32 C51 Replace NEO-6M 3.3V/5V Power Supply

Main Highlights

1.Get 51 Arduino STM32 microcontroller routine.
2.With a USB interface, you can watch the computer positioning effect directly phone line.
3.With the passive ceramic antenna and passive antenna amplifier, make better use of the individual effects.
4.With SMA interface can be directly connected to an active antenna SMA.
5.TTL level, compatible with 3.3V/5V systems.(Size:39*25.5mm)

Show Price

8.1

AITRIP

AITRIP 2PCS GY-NEO6MV2 NEO-6M GPS Flight Controller Module 3V-5V with Super Strong Ceramic Antenna EEPROM APM 2.5 for for Arduino IOT Pi GPIO Flight Control

Main Highlights

Gps module Made of high-quality materials, durable.This product is light in weight, easy to install, and has strong compatibility.GPS module NEO-6M, 3V-5V power supply universal.The module is equipped with a ceramic antenna, the signal is super strong, GY-NEO6MV2 NEO-6M Power: 3-5v
NEO-6M GPS Module EEPROM Compatible for MWC/AeroQuad Antenna Compatible for Arduino Flight Control Aircraft
With data backup battery;With LED signal indicator; Installation aperture: 3mm Default baud rate: 9600 Compatible with multiple flight control modules
NEO-6M is able to provide higher resolution updates, better approximations of location, and more consistent readings
NEO-6M GPS Model: GY-GPS6MV2.Antenna size: 25*25mm.Module size: 25mm*35mm;

Show Price

8.1

DWEII

DWEII 3 Set GY-NEO6MV2 NEO-6M GPS Module NEO6MV2 with Flight Control EEPROM MWC APM2.5 Large Antenna for for Arduino EEPROM APM 2.5 (3PCS)

Main Highlights

GPS modules NEO-6M, 3V-5V power supply Universal
Module with ceramic edge antenna, super signal.
Default baud rate: 9600, Interface: RS232 TTL
With data backup battery;With LED signal indicator
Compatible with various flight control modules that provide GPS computer test software

Show Price

Our Best Overall Choice

Best Choice

9.7

YELUFT

YELUFT 2pcs GY-NEO6MV2 NEO-6M GPS Module Flight Control Module Support 3.3V-5V Power Supply with Ceramic Antenna for Arduino, STM32, Raspberry Pi, ESP32

Editor's bottom line:

“This is the best one we tested. In terms of quality, brand and price, we couldn't ask for more.”

Main Highlights

Accurate Positioning: Based on NEO-6MV2, supports GPS and GLONASS, supports simultaneous tracking of 22 satellites, tracking sensitivity -162dBm, cold-start sensitivity -148 dBm, positioning accuracy up to ±2.5m in open environments, stable positioning even in complex environments such as urban canyons or dense jungles
Low Power Consumption: Supporting 3.3V-5V power supply, the continuous operating current is 67mA, 11mA in standby mode, and 1mA during sleep, which ensures the positioning accuracy while controlling the energy consumption to the maximum, especially suitable for the scenarios that are sensitive to the endurance, and significantly reduces the cost of post maintenance
Hardware Interface: Standard UART-TTL level, support 3.3V/5V dual voltage compatibility, can be directly connected to Arduino, Raspberry Pi, ESP32 and other development boards; 4Pin interface ( VCC, GND, TX, RX), reserved hardware reset pin; baud rate support 4800bps~115200bps (default 9600bps), real-time switching through AT instructions or UBX commands, to adapt to different master performance
Plug and Play: Onboard EEPROM chip operates independently of the main control chip, saves configuration parameters after power failure, and automatically reads the parameters (baud rate, positioning mode, NMEA statement screening) from the EEPROM when the power is on, eliminating the need to repeat the initialisation, and realising Plug and Play
Widely Application: Widely used in vehicle monitoring, UAV navigation, handheld terminals and other scenarios that require high-precision positioning. You can also combine with Arduino, STM32, LoRa module, etc. to quickly build GPS tracker, weather station and other IoT applications

Show Price

Deals are Live

Special Amazon deal ends in: